Roast me, I’m new to it
Good start. If you did that as a test I’d probably hire you. Proof is in the pudding and you can only get better. You need some practice but it’s a really good for a beginner. Some of the work I’ve seen from “certified” welders will make a grow man weep.
Ok well that’s encouraging!! Thanks 👍🏻
I agree. Some of the welders I work up north with scare me😭
I started with MIG/Flux Core and picked up TIG later, and something you realize is that the end of a pass is its own little skill. I’d practice starts and stops on scrap separately so you’re not trying to perfect the whole bead and the crater at the same time. I haven’t run enough 6010 to give rod-specific advice, but practicing on scrap like this is the right way to get comfortable.
Yea that was the aim 👍🏻 practicing laying beads on eachother. Defo need to practice more starts and stops
It’s seriously quite good, as others said, it’s better to do 3 passes, instead of one big. And you really shouldn’t weave more than 12mm (half an inch). Going straight and slow is usually better than fast with weaving, but it kinda depends on the application, anyway good job and keep it up.
If you know how to use an angle grinder and other basic tools, I believe many places would hire you as an apprentice.
Beautiful. Thankyou very much for your feedback. I’ll definitely be resorting to skinnier beads next time. Much easier to manage. I’m not actually learning for an apprenticeship though 😂 just wanting to learn for a few garage jobs, but I figure anything worth doing is worth doing well 👍🏻
Lay the root like you’re using a laser beam. plate that thick ain’t going nowhere. then just keep cutting the weld in half. 1 pass, 2 pass and you might be able to cut the last one into just three passes, 4 would be the safest. Also.. quit weaving.
not shabby for someone who just popped there cherry tho. kudos 🤝
Yea most of the feedback I’ve received is quit weaving and lay straight beads over halves. I’ll give that a try 🫡
Not bad keep practicing, you’re fit up is just about perfect definitely work on tightening up your weave or run stingers, what amp are you running and what diameter of rob are you running looks like 7018
I think it’s 6010 at 100 amps
Root needs work id say tighten it up overall and just practice on the weave work, definitely nothing to roast! Keep it up brotha
🫡🙏🏻 I’ll be giving this a crack today. Thanks for the positive words 👍🏻
Forsure! Let me know how it goes man
Good job for starting out! Three smaller passes will usually be a better weld. One pass in the middle and two on top.
Ok I’ll keep that in mind 👍🏻
Looks like you had the right idea in the 3rd pic. A fat bead with toothy toes is not as strong as solid stringer beads stacked next to each other, next time try to keep your beads about 1/4”, once you put down your first pass put the center of your next pass on one edge (it’s called the toe) of the first pass, it should cover about half of the face of the first bead, then put your 3rd pass on the other toe and it should leave you with a very uniform face that is about the with of 2 beads (1/2”). Make sure every pass that is side by side melts into the one before it, if you aren’t close enough they will make a valley between each other and that leads to cracks.
Ok that sounds tricky, but I’m up for the challenge. I’ll give that a crack 🙏🏻
It sounds trickier than if you just see it. This is basically what you have but rotated 45°, your first pass is centered then each pass after is centered on the toe of the last one this makes them overlap and prevents trapped slag. This example shows how you can really fill in a large area just by stacking beads but for your piece I think you could stop at 3, it all depends on how big you make each bead but keep them small enough to avoid teeth.
Ok beautiful. That makes it simpler. Should I be cleaning each weld before the next bead? Does it matter?
If you’re of you’re welding mig it won’t make the biggest difference. What hurts your weld is paint, oils/grease, mill slag, and rust, if you clean all that off before you start welding it’s not going to re-appear after your first pass. If you are welding with stick or flux-core however, make sure you chip and brush between passes, especially at any divots where the slag might be stuck in, trapped slag will not only cause cracks but under the right circumstances it can cause you to loose your puddle and drip out like crazy. TLDR: clean if there is bad stuff in your path.
Yes the 3 pass and 6 pass helped me so much. I preferred 6 pass over 3 tho
That’s fine by me. Not beautiful but functional.
👍🏻🫡
Cap was practically perfect I’d say tighten the weave up but the root needs work. All in all if you run what you did for the cap I’d say your a great welder definitely a better start then most just tighten up the weave and your solid
Very encouraging to hear that, thank you very much. I will try again today and tighten up my weave 🫡
Salut, si je peux te donner un conseil, fais un premier cordon de pénétration, puis fais des passes en ligne droite sans balayer, tu auras un meilleur rendu et ça sera plus facile pour toi
Merci, mon ami. Je ferai cela demain 🙏🏻
I start to weld 3weeks ago and this one is 2 pass, 1 straight and the other one in zigzag. I made this after 7 day’s practice
Run your weld into it if you can, don’t start over top of the other one. you want to tie it in, not cold roll over it. Backstepping is the way to
And make your points at each end or behind, because the penetration isn’t regular
Pretty nice that
🙏🏻
I mean it. Not perfect sure but the finished weld is good looking, neat, uniform. You’ve got good edges. That’s better than most of the welds I see around site day to day
Very encouraging. Much appreciated 👍🏻
Tighten your bead up and hold the sides until they fill in completely 👍 also could try 2 smaller beads if youre finding the space a bit wide to fill in 1
Yea I’ll be experimenting on holding the sides for longer. Feels very unusual and not natural at all when I tried it today 😂. Is there any advantage strength wise in doing 2 beads instead of a wider bead?
You have to think that the most amount of metal is on the sides and you travel across the middle twice for each edge, so you want to keep the heat on the sides. The metal will go where the heat is so pausing on the sides is how you end up with nice wetted out toes (edges) of the weld and a flatter profile bead.
Ok this is great. Exactly the advice I was after. Thanks so much 🙏🏻🙏🏻. I’ll give this a crack
The strength of the weld does get stronger with stringers because the heat of each pass aligns the molecules of the metal previously laid down. On mild steel, this isn’t really a noticeable factor (arguably), but when welding higher carbon steels, it definitely becomes a factor. The other issue with big weaves is it increases the chances of slag inclusions. If you’re running 6010, you won’t have that issue but on things like 7018 it’s possible. I generally operate on the practice of not moving my rod more than the diameter of what the rod is to either side. So if I’m running 1⁄8, the bead I put down is going to have at most a 3⁄8 manipulation while running. Less if possible.
Ok I’ll definitely keep that in mind. I was running 3mm 6010. So I’ll keep my beads tight from now and see how that makes things
Get rid of the weave and it’ll be almost perfect
This is very encouraging!! I’ll give that a shot today 👍🏻
I wouldn’t surprise if I’ve cut that parts, that looks like my hand writing on that steel..are you in Australia? 😂😂
Hahaha yea absolutely 😂😂 W’s for the win
Well, there’s the problem. You’re welding upside down.
I’m give you \(55/hr and a \)250 per diem
IDK about him but sign me up.
yah if the other guy doesn’t take it I will
Props for starting on something meaty, no a rusted out, thin wall car trailer.
I think he’s been watching the YouTube videos. Of the guy welding.
I hate that I know exactly which guy you mean
Thank you
Bumpy but strong 💪
Slow down and pause in your corners
I’ve seen worse from “certified” welders. Not too shabby honestly.
honestly dude, youre doing great
Fire breathers*
not terrible
Tack it down so the weld doesn’t warp your fitment
I have seen a big mig weld lift up 20,000 pounds when it cooled, no joke. Broke all 5 of his big thumb sized tack welds.