I freehand sawed this in half.
I understand why you wanted to post this. I’m only sorry we weren’t all there to witness.
The product is far more viewable than the process.
With a CROSSCUT saw? Dang, well done. How long did it take?
rip cut saw. hours.
Maybe that’s why it took hours? If you used the saw in the photo that’s a crosscut
Well, no it’s not. It’s a rip cut, it came to me filed a rip cut and I re-filed the teeth and put in the set myself.
Doesn’t matter what you think you did, you have crosscut teeth, so that’s a crosscut saw… The rake is all wrong for ripping and the teeth have fleem. Too many teeth per inch for rip cutting, regardless. What exactly are you saying you did to make this crosscut saw a rip saw?
You have a really aggressive set, which is why it ripped much at all in pine, and I’m sure you had to work really hard for it. I’m not surprised it took you hours. On a piece like you’re cutting, a proper rip cut saw with ~5 tpi should finish that cut in 10-15 minutes.
I’ll take bored af for $1000 Alex.
Its for a project, to avoid a glue up of new wood, as I had already bought these. Waste not.
Only joking man, you crushed that cut!
Luckily you get two boards
the real flex is not telling us how long it took
Op started sawing when the board was still green.
Then milled the log down on either end until they got two equal pieces
What was your approach? Nibble at it from all sides before finishing the middle? Or just sending it through?
If you go all the way around nibbling it will never be straight. Sawing as deep as the saw allowed then rotating, and using the existing walls as a guide to the saw was the process.
I mean, for resawing boards there is a traditional tool called a kerf saw, establishing the perimeter acts as a guide.
You fucking aced this cut, so I’ll bow to a superior craftsman 😂
A small indent was created using a marking gauge to mark the line around as a guide. I colored it in pencil. A rip saw was used.
Meanwhile, I can’t saw a straight line cross cutting a 1x2
I’ll spend 10 minutes setting up the cut, squaring everything, measuring 4 times and it still comes out wrong.
lol can’t cut straight gang unite!
Spend 100 minutes cutting it and you can do this.
Straight lines are a mathematical construct. Technically an impossibility in the physical realm. So it’s good ‘nuff boss.
I’ll be sure to use this one next time my boss gets after me for bad cuts. Cheers!
You are not alone
Dimensional lumber is fucky though, I’ve tried to rip some and it pinched together with enough force to stall out a two HP radial arm saw.
The thought of ripping a 2x4 with an ras is making my butthole pucker
RASs work just fine for ripping you just need some extra long push sticks. They’re better for small shops because rip and crosscuts keep the wood in the same direction, rather than needing lots of clearance to the sides. That said ripping on them would be way nicer and safer with a power feeder.
I can’t saw straight using a table saw and a mitre gauge
I can’t draw straight line using a ruler let alone even think about cutting a straight line.
How did you keep the saw straight? I can’t even cut a roast the same thickness.
Practice and a well-tuned saw
I reject your common sense logic and likelihood that you’re correct. Now tell me how i can do this with neither of the things you mentioned
Aliens.jpg
knew it
Does Bigfoot count?
You HAVE to throw money at it. The only way.
Not at all. If you look for long enough you would be able to find the bones of a good saw and the equipment to set and sharpen it for less than “throwing money at it” money.
And if you know how to set and sharpen the saw you probably know how to use it too and there you go.
Whereas if you throw money at it all you are doing it skipping the “finding what you need for cheap” part. If you don’t know how to use it you still can’t do what OP did.
And a good visible layout line on the entire cut that you follow the entire time. Makes it so much easier.
*a toast
But why?
If you must know. I’m making 2 children’s Viking shields. I bought the rounds so skip a glue up, and then realized they were twice as thick and likely too heavy as a result. Didn’t want to waste the product and spend time in gluing up, so I cut it.
had one circle. now has two circles.
Double circle!
That’s like twice the circle. Damn that’s a lot of circle!
This sounds like a high school algebra problem about cost per area of different pizza sizes.
OP, get one of those giant Japanese hand planes and start shaving off tissue papers from this pine. Infinite money hack!
Circle squared
Meanwhile us mortals are spending thousands on fancy tools and still ending up with door stops.
Nice. People forget how q6ell old saws work. Do you sharpen the saw yourself?
Yes. And the set as well.
Impressive
Now let’s see Paul Allen’s cross cuts
God damn that was a good comment
… Most impressive
Obi Wan has taught him well.
Terrific
Inpossible
How does it feel being God’s favorite?
Now saw them in half again!
The most impressive thing is that it didn’t bow like crazy because of case hardening and internal stress of the wood.
I have done the less impressive version of this quite a few times on my 18 inch bandsaw and at least half of softwood lumber i get is under tension like a suspension bridge.
Impessive job - but mate, life is too short!
Faster than going to buy more wood, prepping, lining up, gluing, waiting, cutting a circle….
If you ever wondered how furniture was made back in the late 17 hundreds to 18 hundreds, now you know… a craftsman becoming one with his tools and enough time spent to master them.
Imagine being in a wood shop all day without a single motor running. Just the sound of wood being worked by hand.
I can’t even slice home made bread as well as this.
Freehanded?!? Pfft, You had a pencil line! /s
I can only imagine how good your bagels look (very jealous)
My guess.
You lined it center, then knifed it, then rotated it as the haft got too close.
Rinse n repeat.
Correct?
Fuck off you did. You did it just because you could didn’t you. DIDNT YOU!!!
The German bread slicing guy would like to have a word
Dude! I’m so sorry I meant for you to glue those together
now saw the other half in half too.
Nice work! I would have to buy two and run them through the planer 🤣
You are a better man than me, that’s for sure
I’d have 6 crescent moons somehow